Curious about how to properly clean your Puffco Peak?

You’re in good hands with the crew at Dank Riot!

We have gathered clear and easy-to-follow instructions for cleaning the Puffco Peak, the first generation of Puffco’s smart rigs.

You will be ready to make your Peak appear like it was purchased yesterday by the time you reach the conclusion of this guide.

How To Use and Clean a Puffco Peak, Step By Step:

The following is a guide on how to begin using and maintaining your new apparatus.

1. Charge up your dab rig

Even though your Puffco Peak vaporizer will arrive pre-filled with some liquid when you first get it out of the box, you should still fully charge the batteries before using it for the first time. Simply use the USB cord that comes provided with your dab rig to connect it to any charger. After it has finished being charged, it will turn off automatically. A full charge will allow for approximately 30 dabs, which is equivalent to approximately 2.5 hours of use.

2. Prepare your device

After you have finished charging your device, you will need to carefully fill the glass attachment until it is just over the air holes, taking care not to overfill it. Always ensure that the attachment has been refilled with water before you attach it to the base to eliminate any potential for water damage.

Align the inlet hole on the glass attachment with the atomizer on the base of your device before attaching it. Place the glass attachment on the base of your device. After that, carefully insert it into the base. There shouldn’t be any significant amount of resistance to this.

To ensure that everything is functioning properly, check the airflow by inhaling through your device when it is turned off. After that, you can turn it on by depressing the power button for three seconds in order to activate it. With just one click, you can quickly switch between the four different temperature settings.

3. Load up your concentrates

After you have ensured that your gadget is functioning properly, you can then begin loading it. When loading your Puffco Peak, you should never use your fingers because they can cause your material to deteriorate. Instead, you should make use of the appropriate dabbing tool. You’ll be happy to know that the Peak comes with a fundamental loading tool to assist you in serving your material.

In order from coldest to hottest, the temperatures range from blue to green to red to white, with white being the hottest temperature. If you load more material into your apparatus, you will need to raise the temperature to accommodate the additional mass. However, take care not to overfill the container; doing so puts you at danger of liquid leaking into the atomizer, which can cause permanent harm to the device.

4. Test out your device

After you have everything loaded up and are ready to go, place the provided carb cap on top of the atomizer, and give it a double click to begin using it. If it’s getting hot enough, the light should start flashing to let you know. When it is finished, it will notify you by flashing three times and providing haptic feedback. The next step is to take a deep breath in.

When you inhale the vapor for the first time, do so carefully, as if you were sipping a bowl of hot soup. You should be able to get a good taste of your concentrates if everything went according to plan. Perform several tests on your equipment, and when you are comfortable, you can begin vaporizing. If you find that you need additional time to evaporate, you can double-click the button to add 15 seconds to the end of your session while also increasing the temperature, which will make it easier for you to complete the process of vaporizing your substance.

5. Clean your Puffco Peak

It is highly recommended that you clean your Peak as soon as you are done using it. Simply insert a cotton swab inside the chamber and allow it to absorb any traces of residue left behind.

However, after a few usage, you will need to clean your item a little more carefully than you did initially. Before beginning this form of cleaning, ensure that your device is turned off and that the container you will be using is at room temperature. You have the option of either allowing the container made of borosilicate glass to soak in isopropyl alcohol for one hour or employing a glass cleaning solution in order to save the waiting time. After that, use a cotton swab to remove anything that is still there. Because doing so raises the likelihood that you will damage the atomizer, you should steer clear of removing the bowl from its jacket and avoiding using a cotton swab to clean it.

A cotton swab that has been dipped in isopropyl alcohol makes it possible for you to finally clean the bottom of your device. If you take good care of your Puffco Peak, it will serve you well for many years to come.

Why should you get a Puffco Peak?

The Puffco Peak is a streamlined and portable rig that is best suited for experienced users who are looking to consume their preferred powerful concentrates in a cutting-edge device. Anyone looking for a high-tech method of eating concentrates and with the budget to buy it should absolutely consider adding the Puffco Peak to their collection. It is an absolute necessity in any collection that contains concentrates. After all, this vaporizer is not the least expensive one available, but it is without a doubt up there with the very best.

Puffco Peak Cleaning Instructions

Remove

Disconnect the Puffco Peak glass attachment in a careful manner so that you can get started on the cleaning process. You should be able to simply remove the glass by pushing it away from the base in a careful manner.

Wait until the ceramic bowl has reached room temperature before attempting to remove the atomizer from its base.

Take out the atomizer and unscrew it in the opposite direction of the clock until it can be pulled out of the base.

It is possible to disassemble the Puffco Peak atomizer into its four component parts; however, doing so is not something we encourage doing.

Soak

Isopropyl alcohol 99% should be added to your Puffco Peak glass until it is approximately halfway full. Next, the glass should be carefully shaken while the opening is covered. This ought to get rid of practically all of the residue inside.

Waiting the night allows for a more thorough washing of the glass.

After it has been washed, give it a final rinsing in water, and then let it air dry entirely.

Spend at least an hour and a half soaking your finished atomizer and carb cap in alcohol that is 99% isopropyl.

The fact that the isopropyl alcohol turns a brownish tint as the pieces soak in it is a clear indication that the treatment is effective.

When cleaning your atomizer, you should not make use of any water at all. The atomizer is susceptible to damage by water, which might result in the device becoming inoperable.

To complete the process of cleaning your atomizer, dip a cotton swab in 99% isopropyl alcohol and then use it to carefully wipe the gold connector pin that is located on both the atomizer and the base.

WARNING: Do not let your Puffco Peak base get wet. This could lead to it breaking as a result.

After the preceding processes have been finished, wait for all of the components to thoroughly dry out.

Reconnect

When you are ready to reassemble the device, begin by reattaching the atomizer to the base by tightening the screws.

To use your Puffco Peak glass, start by filling it with water up to the point where it covers the air holes. Always make sure that you are filling your glass attachment at a distance from the base of the Puffco Peak to avoid injuring it.

Aligning the air holes on the glass with the holes in the base is a necessary step before reattaching the glass to the base.

After ensuring that all of the components are properly connected, you should check the flow of air by taking one or two draws.

After roughly 20 usage, we recommend giving your Puffco Peak a good cleaning.

Dry Run

The final stage of the cleaning procedure consists of allowing your Peak to complete an entire heat cycle.

Turn on your Puffco Peak, and make sure the temperature is set to the White setting.

Give your Peak some time to warm up and run through its entire cycle.

Perform this process a few times before loading your concentrates for a genuine session so that you can get the hang of it.

Extra cleaning tips

Reduce the amount of concentrate you use while loading your ceramic bowl in order to cut down on the number of times your atomizer needs to be cleaned.

Experiment with a variety of temperatures and load sizes until you find a combination that enables you to get the most out of your concentrates while minimizing the amount of waste that is produced in the process.

Rinsing the glass attachment of the Peak at least once a day to prevent residue from filthy water buildup is an additional essential step in the process of keeping your Peak clean.

If you adhere to our cleaning recommendations and follow our helpful hints, your Puffco Peak will continue to operate at its peak level for as long as possible.

How To Clean Puffco Peak Pro?

Puffco Peak Pro

You performed the necessary research, decided to go for it, and in the end, you decided to reward yourself by purchasing the magnificent Puffco Peak Pro. Congratulations for getting this far; you have demonstrated excellent judgment thus far.Your next important choice should be to ensure that it receives the utmost care so that it can be enjoyed for a very long time. It is inevitable that everyone who uses it will eventually make a mess of it, no matter how careful they are. In this instruction manual, we will cover everything you need to know to properly clean and maintain your Puffco Peak Pro.

How often should I clean my Puffco Peak Pro?

Puffco suggests that customers clean their devices on a regular basis to ensure the best possible experience. They do not specifically indicate how frequently because the answer to that question is contingent on how frequently it is used. If you use it every day, we advise giving it a deep clean once each week. Every time the battery is completely drained to the point that it needs to be recharged, you should give it a thorough cleaning. If you observe that there is excess flooding or if the gadget gives you a red-blue reaction, you should soak the atomizer.

TIP: If you want to avoid having to clean your chamber more regularly, it is a good idea to swab it with a cotton swab that has been soaked in ISO after each usage.

In this instruction manual, we will cover everything you need to know to properly clean and maintain your Puffco Peak Pro.

Puffco Peak Pro Cleaning Guide: You Will Need…

• Cotton Swab/Q-Tip
• 99%+ isopropyl alcohol

TIP: You are able to make do with a lower percentage if you are unable to obtain 99% of what you want. Isopropyl alcohol with a percentage of 99% is recommended by Puffco since lower percentages contain a higher amount of water, which “could potentially cause issues.”

Disassemble Puffco Peak PRO

Atomizer/Chamber

1. Remove the cap.
2. Turn your atomizer counterclockwise to unscrew it from the base.
3. Remove the atomizer

Glass

1. Maintain your grip on the base with one hand while snatching the glass with the other.
2. To remove the rear of the glass from the base, first unclip it and then gently pull it outward until it is free.

What To Clean?

The chamber of your Puffco Peak Pro is the component that requires the most attention to detail regarding cleanliness. This is due to the fact that it has the greatest amount of interaction with concentrates. An unpleasant dabbing experience could be brought on by an excessive buildup of residue and filth. Additionally, it is of the utmost need to maintain a clean base and glass in order to prevent the accumulation of dirt.

How to Clean the Puffco Peak Pro: Chamber/Atomizer

Light Clean

1. Simply take a cotton swab or a Q-tip and soak it in the isopropyl alcohol.
2. Remove any dirt or residue from the gold connection points that are located on the bottom of the chamber using a cotton swab.
3. To remove any residue from the chamber, use a cotton swab.

TIP: According to our findings, the best results may be achieved with this strategy when the space being utilized has only been recently utilized and is still slightly warm. Before you attempt to handle it, kindly wait until it has cooled off.

Deep Clean

• Fill a glass or beaker with the alcohol that has an ISO of 90% or above.
• At a minimum of half an hour, the container should be submerged.

Warning: Under no circumstances should you try to submerge the chamber in water. Ceramic that comes into contact with water has the potential to sustain damage.

How to Clean the Puffco Peak Pro: Glass

1. Put some isopropyl alcohol in a glass or beaker.
2. After thirty minutes, completely submerge the glass in the beaker.
3. After soaking, remove the object and give it a thorough cleaning with fresh water in order to eliminate any remaining alcohol.
4. Before reattaching the glass to the base, be sure it has completely dried off.

Warning:  You should make every effort to prevent water from getting into the lower chamber of the glass.

How to Clean the Puffco Peak Pro: Base

1. Simply take a cotton swab or a Q-tip and soak it in the isopropyl alcohol.
2. To ensure that the connection is established correctly, swab the gold connection points on the base.
3. Make a swab of the airway using your q-tip.

Warning: Wait until all of the components are completely dry before reassembling them after cleaning them. Because it is electric, avoid getting the base wet at all costs; doing so will likely render it useless.