How to Clean Dyson V8

In the following paragraphs, we will demonstrate how to clean a Dyson vacuum as well as how frequently you ought to clean it.

How Often Should You Clean Your Vacuum

It’s possible that the frequency with which you should clean each component of your vacuum will vary. As a result, we have produced a brief table for your reference.

In addition, it is recommended that you purchase a new vacuum at least once every ten years. You are able to examine the Dyson vacuums in this location.

How to Clean Dyson V8

Let’s get started by cleaning the filter on your Dyson.

How to Clean Dyson V8 Filter

Dyson V8 has two filters:

• Pre-motor filter. This is located exactly in the center of the cyclones.
  
• Post-motor filter. There is visibility behind the motor.
  

It is imperative that only cold water be used for cleaning these filters.Do NOT any detergents.

Steps on How to Clean the Pre-Motor Filter

• Pulling it out of its housing will allow you to remove the pre-motor filter.
• Get rid of all the dust.
• Then rinse it under running water.
• Squeeze out any excess moisture.
• Before reattaching it to the vacuum, let it air dry for at least one day to ensure that it is entirely dry.

You don’t have to do this if you don’t want to, but if you do want to clean the section of the filter that’s inside the housing, you can remove the top of the filter using a blunt instrument.

Put a light pressure on the clip. When the lid is off, it is much simpler to clean the component that is inside.

You can also purchase a second filter to use while waiting for the previous one to finish drying entirely if you want to avoid any downtime.

Steps on How to Clean the Post-Motor or HEPA Filter

• Turning it in the opposite direction of the clock will remove the filter.
• Remove unnecessary dust.
• Rinse your filter.To ensure that the water is filtered thoroughly, run it over the exterior of the filter. To remove dirt that is very tenacious, you can use your hands to give it a light rubbing.
• Give your filter a good jolt to get the sediment out.To use your filter, fill it with water from the tap. To eliminate dust and debris, you should first cover the ends with your hands and then vigorously shake them.
• Before you attempt to reinstall it, give your filter at least one full day to dry out.

You can check it out below if you need an additional filter or if you want to replace your current filter with a new one:

• Dyson Pre-Motor Filter
• Dyson Post-Motor Filter

Cleaning a Dyson V8 Brush Head

The Dyson V8 comes with two distinct types of cleaning heads: the fluffy attachment and the normal brush.

Even the Dyson nozzles might have some characteristics that prevent tangles from forming, it is critical to check on and clean the brush head on a regular basis. Any accumulation of debris in the system will result in increased friction and wear, neither of which is beneficial to the system’s performance over the long term.

How to Clean V8 Fluffy Tool

• Remove the plastic clip. Underneath the fluffy attachment is where you’ll find a plastic bolt that secures the roller bar in place. To get rid of it, you can try using a coin.
  
• Take out the roller attachment. A graphic of an arrow will be displayed on the right-hand side of the tool. Simply lowering this side allows you to remove the soft roller from the device. After this part has been removed, another, smaller roller component will be taken out as well.
• Clean thoroughly. When all of the components are removed, it is much simpler to clean the crevices and spaces in between them. You are able to clean either of the rollers, but you should not use any detergents.
• Refit the rollers. Before you replace the rollers, be sure that they have been well dried out.
  

How to Clean V8 Cleaning Head

• Remove the cap. Using a penny will allow you to unscrew the cap that is securing the brush in place.
• Take out the brush. As you turn it, the cap will dislodge and fall off. Before you can clean it, you will need to remove the lid and the brush from it first. Cut the hair that is wrapped around the brush using a pair of scissors. It is imperative that you remember to clean the wheels as well as the ball system. Additionally, check to see if any debris has accumulated on the axles. The next step is to get a piece of microfiber and clean the various components of the nozzle.
• Refit the brush. After you have finished cleaning it, you are now able to reattach the brush that was removed before. Maintain the use of a coin for the twisting and locking action.

Clean a Dyson V8 Cyclone

Now that we’ve gotten this far, it’s time to clean the cyclone, but before you do anything further, you should be aware that doing so could render the guarantee null and void.

Therefore, if your Dyson is still covered by the manufacturer’s guarantee, I would strongly advise against opening your cyclone.

And one more thing, you should only proceed with this if you are positive that you will be able to put it back together again. It sounds like you are the type of guy who is into electronics or who has experience with doing things on their own.

Steps on How to Clean V8 Cyclone

• I would suggest taking some photos of each stage before you start disassembling the V8 cyclone. That way, you will have a reference when it comes time to put it back together.
• Take out the filter for the pre-motor.
• Clear out the wastebasket.First, the red lever needs to be pulled to empty the container, and then it needs to be pressed in order to open the lid of the dust container. You can put it to the side for the time being and clean it later if it is unclean.
• Take apart the cyclone in its entirety. Now that the outer shell of the dustbin has been removed, you need to locate the red lever and pull it. The entire assembly is then brought higher by sliding it. You will find four Torx screws; in order to remove them, you will need a torque screwdriver. After the screws have been removed, the component can be removed and stored in a secure location in a ziplock bag.
• Taking off the screen filter’s fasteners.It is possible to use a tool with a flat surface, such as a flat screwdriver, and to gradually pull it upward while rotating the filter. As you continue to pull, you will feel the clips become less secure. As soon as you have undone all of the clips, remove the mesh filter and clean it with a fresh microfiber towel. Or you might wash it with water, but be sure to dry it thoroughly afterward.
• Take out the cyclones.As soon as you remove the mesh filter, you’ll be able to access the Torx screws holding the outer cyclone shell. After removing the four screws, pull off the cover, and you will see how unclean it is underneath. The inner component can then be removed; there are no screws used to secure it, so you simply need to take it out.
• Disassemble the top cyclone assembly. The cyclones have four Torx screws inside and two outside. You may need a little help with a flashlight to find the inner screws. Once you’ve located and removed all the screws, dismantle it. Store all the screws in the ziplock bag so you won’t lose them.
• Clean the component of the cyclone.Clean all the parts with running water. You can use an old toothbrush to remove stubborn dirt. Don’t scrub too hard as it may damage the component. After washing, let it dry completely before placing it back.

Reassemble Dyson V8 Cyclone

• Join the black gasket to the black component using the appropriate screws. The depressions are oriented so that they face outward.
• Reattach the cover to the cyclone.
• After that, attach the red gasket.
• Join the inner cyclone together. Make sure that the five ports of the inner cyclone are in their correct positions.
• After that, the outer cyclone should be installed, and the screws should be tightened. It is held in place by a total of six screws, two of which are positioned on the exterior. And in the cyclone, there are four screws that need to be tightened.
• Following that comes the inner cover of the cyclone. You just have to give it some more force.
• Fasten the outer cyclone in place. Put it together using the four screws.
• The mesh filter is supposed to come next. The mesh filter is only being held in place by clips. Just give it some downward pressure until you hear the clips securing themselves to the frame. Check to see that the mesh filter is secured in a secure manner.
• The red lever needs to be connected to the cyclone assembly at this point. Use the four screws to secure the piece.
• To mount the cyclone assembly on the motor, slip it on there. Observe carefully to see whether you can hear the clicking sound.
• Last but not least, reattach the dust bin that has been cleaned.

How to clean Dyson V8 Vacuum?

In short: Before beginning to clean the Dyson V8, you must first take out the dustbin. After that, empty it, and use a clean towel to wipe it down to remove any dirt, dust, or other debris. Take out the filters and give them a good cleaning. To accomplish this, you must first remove the filters by depressing the two tabs on either side of them and then drawing them out. After that, give them a quick wipe down with a clean towel, and then replace them. Finally, take off the suction tube and clean it, as this component of your vacuum cleaner needs to be cleaned on a regular basis in order to function properly.

Now that we’ve gone over all of the steps, I’m going to go over each one in deeper detail using info-graphics and video-graphics below so that you can easily do this operation without running into any problems.

Step 1: Gather cleaning aid

In order to properly clean your Dyson V8 vacuum, you will first require the following items.

• Rubber gloves.
• Trash container.
• A Screwdriver.

Step 2: Unplug Your Dyson V8

Before you start cleaning your Dyson vacuum cleaner, make sure the power cord is unplugged and that it is turned off.In addition, you need to remove any accessories, such as extension wands, soft brush tools, and hoses, that you might have. The process will be sped up and it will make your job far safer, lowering the likelihood that you will receive an electric shock.

Step 3: Remove and clean the Dyson v8 filter

Because it is such an important component in the overall cleanliness of your home, the filter in your vacuum should be cleaned on a regular basis. It is effective at capturing particles of dust, pollen, germs, and grime. This indicates that the filters will eventually require some sort of cleaning in order to function properly.

You will notice that many of the Dyson filters have a purple colour, and you may discover them close to the cyclone. The Dyson V8 Vacuum has not one, but two filters: one is a pre-motor filter, and the other is a post-motor/Hepa filter. Therefore, you are need to clean the two of them.

Pre-motor Filter

Follow the procedures below in order to clean the pre-motor filter on your Dyson V8:

1. Take remove the filter for the pre-motor.
2. Perform a thorough cleaning while the water is flowing.
3. Scrubbing the filter material with a scrubby might be harmful to it. So avoid that.
4. Wringing it out will remove any excess water that may have accumulated.
5. Before fully reattaching it to the vacuum, you should give it some time to dry.

post-motor/Hepa filter

Please follow the procedures below in order to clean the Dyson V8 Hepa filter:

1. Turning it in the clockwise direction will unlock it, and then you may take it off.
2. Washing it under running water can eliminate any filth that may have accumulated on it.
3. Give the filter a thorough shake and wait for it to totally dry off before you attempt to reinstall it.
4. Because Dyson cyclones are so successful at keeping dirt particles away from them, the HEPA filter that comes after the motor does not need nearly as much cleaning as the filter that comes before it.

Step 4: Clean Dyson v8 head

The head of the Dyson V8 vacuum has not one but two different kinds of brushes. The first is a normal brush, while the second is a fluffy attachment for the brush.

Even though both of the nozzles are resistant to being entangled with one another, this component still has to be examined and cleaned on a regular basis. Any particle blockage will increase friction and wear, which is horrible for the durability of the component.

Fluffy attachment

In order to clean the fluffy attachment for the Dyson V8, please follow these steps:

• First, remove the plastic clip.
• Take out the roller attachment.
• Clean it thoroughly with cold water.
• Then let it dry.
• Finally, reinstall the rollers.

Standard Brush/main brush

To clean Dyson v8 main cleaning head, follow the below steps:

• Remove the cap by using a coin
• Take out the Brush.
• Now clean the Brush with a soft microfiber cloth.
• And finally, reinstall the Brush.

Step 5: Empty and clean the Dyson v8 bin/canister

The following method involves totally cleaning the dust canister or bin of your Dyson V8 vacuum cleaner. In most cases, the dust canister will be situated just below the cyclones. On the bottom of some of the models is a button labeled “bin release” that is colored red. You can disengage the dust container from the vacuum cleaner by pressing this button. Depending on the model, it could be situated in a different area, but it shouldn’t be too far away from the main body of the vehicle. Check the instruction manual if you are unsure where it is located.

It is possible for the red lever, which is the button that releases the bin, to become jammed, which would prevent you from being able to empty the trash can. If this is the case, read our comprehensive guide to learn how to free the button that releases the trash can.

Once you have located the button, you will need to press it in order to detach the base and throw away the debris. Make sure to give it a good shake in order to remove as much dirt as you can from it. You can clean the inside of the dust canister with a microfiber cleaning cloth.

When cleaning up the dust canister, Dyson recommends not using any kind of washing powder because chemicals might cause the material to become sticky. When it comes to cleaning the Dyson cyclones, some user instructions advise against using any kind of liquid, even water. You can use a device that uses compressed air to clear the dirt from the cyclones if they have been clogged with the dirt.

Step 6: Remove the clog from the hose

The suction power of your hose may decrease over time because it becomes blocked with debris. When you are cleaning your vacuum, be sure that the hose is disconnected from your Dyson. In many instances, there is a button that can be used to detach it from the wand. The next step is to inspect the interior of the hose for any debris. To unclog the hose, take the handle of a mop and force it through the opening.

When cleaning the vacuum hose, it is best to steer clear of strong chemicals wherever possible. This could result in damage that cannot be repaired. To get rid of germs and bacteria in your home, you should make your own household cleaner out of white distilled vinegar instead.

Put one cup of vinegar and some warm water in the sink that’s in your kitchen. After that, you should submerge your hose in the solution. After ten minutes, run some warm water through the hose from the faucet. Make a U with your hand and your hose. It’s possible that this will make the process simpler. Before you reattach your vacuum, give it some time to totally dry out. This could take up to a day’s worth of time. So be patient!

Step 7: Lastly, clean the entire vacuum

Last but not least, do not forget to clean the exterior of your Dyson vacuum. You’ll need a damp microfiber cloth this time, but be careful not to completely submerge your gadget in water! In addition to that, you should think about cleaning the soleplate and wheels of your vacuum. It’s possible that the dirty flooring and carpets that you’re tripping over are also carrying filth.

You can accomplish this by making a solution out of vinegar that has been diluted. Before you use your vacuum again, just make sure that it has been totally dried out.

FAQs

Q. Can I wash my Dyson V8 vacuum head?

No, you are unable to clean the head module of your Dyson V8 vacuum cleaner. According to Dyson, “The cleaner head housing is not washable.” For the best possible cleaning results, the brush bar should be washed with water alone.

Q. Can I wash my Dyson V8 clear bin?

You are able to clean your Dyson clear bin; but, you must use extreme caution so as not to crack the transparent plastic. To clean the trash can, you can make a solution of some gentle soap and water.

Make sure you give it a complete rinsing so there is no trace of soap left behind. You should also refrain from using abrasive cleaners or scrubbers on the trashcan because doing so might cause the plastic to become ruined.

Q. Can I wash the cyclone part of my Dyson v8?

The cyclone in your Dyson vacuum is a one-of-a-kind filter that employs centrifugal force to separate larger dust particles from the finer ones. Technically speaking, you can wash it. When using tap water to fill the machine, the official Dyson instructions recommend giving it a light shake while doing so.